조회 수 0 추천 수 0 댓글 0
?

단축키

Prev이전 문서

Next다음 문서

크게 작게 위로 아래로 댓글로 가기 인쇄 수정 삭제
?

단축키

Prev이전 문서

Next다음 문서

크게 작게 위로 아래로 댓글로 가기 인쇄 수정 삭제
If you are making your carport from wood or steel, here are the basic steps required: Set out the perimeters
Clear the area where the carport companies is to be erected and put out the perimeters. Begin by measuring out from the wall of your home to the desired width (3 metres is normal ) and measuring parallel to your house (6 metres is normal ), and then driving pegs into the ground to mark all the four corners. ) Then, insert easy hurdles into the floor only a bit further beyond each peg in prep for your series lines. Attach string lines
Stretch series lines from one hurdle to another (each string line should be touching 2 pegs--if not, adjust accordingly), developing a rectangle the size of the carport. Remove the pegs, and the corners created by the string are where the concrete pole footings will be found. Carports Pretoria can assist you.
3.
Check the space is square
Measure diagonally from one corner to the other to guarantee the pegs are square, and if not, adjust accordingly.
4.
Dig holes for posts
Dig a hole at each of the four corners to house your articles. The measurements and depth of your pockets will be determined by your soil type and therefore are normally covered in your construction permit.
NOTE: In case you're using steel poles, these will typically be fastened via mounting plates onto a cement slab using a hammer drill to produce the bolt holes. Pour the cement
Mix enough cement for carport companies a single post hole at a time, and put it in the pit. Take a post saddle (a U-shaped metallic saddle using a'standoff' underneath to help stop the pole from rotting) and push it into the centre of the hole, making sure the saddle part stays 25mm clear of the wet cement. Use a spirit level to make sure it's completely flat, then repeat the process for the other 3 holes. Carports Pretoria can help you. Put up the articles
After departing the cement to place over a week or so, you can then install the posts. Have a friend hold the pole in the saddle at the same time you make it just vertical with the spirit level. Then, drill a hole through the saddle holes and right through the pole, insert a coach nut and bolt and tighten to hold the pole vertical. Repeat with the other three posts. Produce a datum line
That is really a line to ensure the roof of your carport is flat. Mark among the vertical posts using a pencil in the height that you want the roof to be, then, use your soul level to indicate the specific same height for all four articles. Then unbolt the articles and cut them all to the desired roof height.
8.
Attach the beams
While you have the posts on the floor, cut the housings (notches) for the beams with your saw. Put up the articles again and with the Support of a friend. Then, using ladders, place the side beams so they are resting in the housings, flush with the exterior of their carport. Drill two holes and secure the negative beams to the posts with coach screws.
NOTE: With steel beams, you'd join the centre beams to the edge beams through bolts through the splice plates, then join the border beams to produce a box framework.
9.
Attach the rafters
First, set the autumn of the roof for rain to run off. Do this by beating a nail at front of a few of the side beams, and running a series line down to the other end and attaching a nail 40mm lower compared to another nail (this is your run-off layer ). Repeat on the other side beam, steel carports then nail a batten down on the inside of each side beam along the string lines. After that, cut on your battens into the width between both sides and then match one every 900mm or so by massaging them securely. Carports Pretoria can assist you. Fit the gutter and downpipe
Begin with the gutter which can go along the lower end of the carport (the rear ). Attach it to the back beam utilizing gutter clips and be sure it's a slight run-off to be sure the rainwater runs down the downpipe. Then, join the downpipe to the nearest stormwater drain. Build the roof
Lay your steel roof sheeting across the rafters whilst making sure it's within the negative beams, then combine it together with proper fasteners. In the end, apply cap flashing over where the roof meets the border of the beam to get a totally watertight border.

List of Articles
번호 제목 글쓴이 날짜 조회 수
1913 How Does A Learnership Work? Winifred55L23121772 2019.07.12 0
1912 The 4 Types Of Exercise You Need To Be Healthy HoraceBaldwin174667 2019.07.12 17
1911 How To Choose The Right Lawyer RosellaKovach027393 2019.07.12 0
1910 10 Tips For Choosing A Plumber ChauSuttor32346 2019.07.12 20
1909 Choosing The Right Plumbing Company CharityNarvaez032 2019.07.12 17
1908 Why You Need BBBEE Consulting Services CelindaLavin58984734 2019.07.12 0
1907 The 4 Types Of Exercise You Need To Be Healthy FredericMarden27819 2019.07.12 0
1906 Why You Need BBBEE Consulting Services ScarlettMaum677 2019.07.12 0
1905 Why You Need BBBEE Consulting Services BillDunkel84717500413 2019.07.12 0
1904 Business Intelligence Software KrystynaTafoya09 2019.07.12 0
1903 Tips On How To Choose The Best Lawyer DarioLittleton743278 2019.07.12 0
1902 The 4 Types Of Exercise You Need To Be Healthy Jillian61450326101235 2019.07.12 0
1901 What Is A Learnership? DellVergara21618 2019.07.12 0
1900 The 4 Types Of Exercise You Need To Be Healthy DiannaLoomis1673007 2019.07.12 0
1899 The 4 Types Of Exercise You Need To Be Healthy LowellRiver363936815 2019.07.12 0
1898 The 4 Types Of Exercise You Need To Be Healthy MarionCaskey6268 2019.07.11 0
1897 5 Easy Plumber Pretoria Repairs JamalBolinger39848 2019.07.11 0
1896 The 4 Types Of Exercise You Need To Be Healthy Flossie14P715621732 2019.07.11 0
» How To Build Your Carport In 11 Steps By Carports Pretoria PenelopePerdue2999 2019.07.11 0
1894 5 Easy Plumber Pretoria Repairs LindaCockle0426088062 2019.07.11 0
Board Pagination Prev 1 ... 42 43 44 45 46 47 48 49 50 51 ... 142 Next
/ 142